Symmons S-66-2-LAM-TRM-RP Bedienerhandbuch PDF herunterladen (Seite 2)

INSTALLATION OF:

SHOWER SYSTEMS AND

TUB/SHOWER SYSTEMS

Tools required for installation of this prod-

uct are: Phillips screw driver, tubing cutter,

teﬂon tape, soldering equipment, adjustable

wrench and channel-lock pliers.

1. Install piping and ﬁttings with valve body

as shown in Figure 2 or 3. IMPORTANT:

Valve rough-in is 2 3/8” +/- 1/2”

from CENTERLINE OF SUPPLIES TO

FACE OF FINISH WALL. Install so that

line indicated on rough-in plaster shield

(T-176) on valve is ﬂush with ﬁnish wall

as shown in Figure 1 (See Figure 5 for

ﬁberglass wall installation).

Tub/Shower System (Figure 2)

Model A

Pipe shower head from outlet marked

“S” and to tub spout from outlet marked

“T”. The diverter mechanism in this

valve is designed so that it cannot be

subject to any back pressure, other than

is imposed by the spout supplied with

this package. DO NOT SUBSTITUTE

OTHER OUTLET ACCESSORIES FOR

THE TUB SPOUT (SUCH AS HOSE

AND SPRAY, SHOWER HEAD, BODY

SPRAY, LEDGE SPOUTS, ETC.) OR

ANY PIPE ADAPTER OR ADDITIONAL

FITTINGS (SUCH AS PEX, ETC.)

THAT CAN CAUSE BACK PRESSURE

THROUGH THE VALVE. Install HOT on

left and COLD on right according to valve

markings.

Shower System (Figure 3)

Model B

Pipe to shower head from outlet marked

“S”. DO NOT REMOVE PLUG FROM

OUTLET MARKED “T”. Install HOT on left

and COLD on right according to valve

markings.

Tub/Shower, Shower or Tub

System (Figure 2A)Model C

Tub/Shower System: The valve in this

system has a built-in choke for use with a

diverter spout. Follow piping instructions

for Model A valve.

Shower System: Pipe shower head

from outlet marked “S”. Install either the

included copper sweat or 1/2”-14 NPT

plug (pipe sealer required) into the outlet

marked “T” (see ﬁgure 3A).

Tub only System: Pipe tub spout from

outlet marked “T”. Install either the

included copper sweat or 1/2”-14 NPT

plug (pipe sealer required) into the outlet

marked “S” (ﬁgure 3A).

2. When ﬁnishing tile wall PULL OFF ENTIRE

PROTECTIVE PLASTER SHIELD (T-176). If

ﬁnish wall obstructs removal of plaster

shield, break off outer edge along perfo-

rations (if necessary, carefully use sharp

blade to facilitate removal). After plaster

shield is removed FILL AREA AROUND

VALVE BODY WITH GROUT OR PLASTER.

3. Turn on hot and cold supplies, valve will

not operate unless both hot and cold

water are turned on.

4. Unscrew dome cover (T-19/20) and tighten

packing nut (T-17) for positive frictional

resistance to handle turn throughout adjust-

ment cycle and at shut-off position. Check

valve cap, packing nut, diverter spindle

o-ring and all valve, pipe and ﬁtting connec-

tions for leaks.

5. SET LIMIT STOP SCREW AS DIRECTED

4 3/4"

120mm

approx.

40"

1016mm

6 1/4''

158mm

FIGURE 2

Model A: Tub/Shower System

nish wall face

4" (101mm) Max

2

3

8

''

60mm

1

2

''

supplies

C

L

+

3" (75mm) Min

plaster shield

(T-176)

FIGURE 1

FIGURE 2A

Model C: Diverter spout installation

1 2 3 4 5 6 7 ... 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare